Documented the lighttpd-support in `collectd(1)' and `collectd.conf(5)'.

[collectd.git] / src / collectd.conf.pod

diff --git a/src/collectd.conf.pod b/src/collectd.conf.pod
index f521571..803df8b 100644 (file)
--- a/src/collectd.conf.pod
+++ b/src/collectd.conf.pod
@@ -118,6 +118,10 @@ the following snipped to base your Apache config upon:
     </Location>
   </IfModule>
 
+Since it's C<mod_status> module is very similar to Apache's, B<lighttpd> is
+also supported. It introduces a new field, called C<BusyServers>, to count the
+number of currently connected clients. This field is also supported.
+
 The following options are accepted by the C<apache>-plugin:
 
 =over 4
@@ -185,6 +189,47 @@ at all, B<all> partitions are selected.
 
 =back
 
+=head2 Plugin C<dns>
+
+=over 4
+
+=item B<Interface> I<Interface>
+
+The dns plugin uses B<libpcap> to capture dns traffic and analyses it. This
+option sets the interface that should be used. If this option is not set, or
+set to "any", the plugin will try to get packets from B<all> interfaces. This
+may not work on certain platforms, such as MacE<nbsp>OSE<nbsp>X.
+
+=item B<IgnoreSource> I<IP-address>
+
+Ignore packets that originate from this address.
+
+=back
+
+=head2 Plugin C<email>
+
+=over 4
+
+=item B<SocketGroup> I<Group>
+
+If running as root change the group of the UNIX-socket after it has been 
+created. Defaults to B<collectd>.
+
+=item B<SocketPerms> I<Permissions>
+
+Change the file permissions of the UNIX-socket after it has been created. The
+permissions must be given as a numeric, octal value as you would pass to
+L<chmod(1)>. Defaults to B<0770>.
+
+=item B<MaxConns> I<Number>
+
+Sets the maximum number of connections that can be handled in parallel. Since
+this many threads will be started immediately setting this to a very high
+value will waste valuable resources. Defaults to B<5> and will be forced to be
+at most B<16384> to prevent typos and dumb mistakes.
+
+=back
+
 =head2 Plugin C<hddtemp>
 
 =over 4
@@ -199,6 +244,41 @@ TCP-Port to connect to. Defaults to B<7634>.
 
 =back
 
+=head2 Plugin C<irq>
+
+=over 4
+
+=item B<Irq> I<Irq>
+
+Select this irq. By default these irqs will then be collected. For a more
+detailed description see B<IgnoreSelected> below.
+
+=item B<IgnoreSelected> I<true>|I<false>
+
+If no configuration if given, the B<irq>-plugin will collect data from all
+irqs. This may not be practical, especially if no interrupts happen. Thus, you
+can use the B<Irq>-option to pick the interupt you're interested in.
+Sometimes, however, it's easier/prefered to collect all interupts I<except> a
+few ones. This option enables you to do that: By setting B<IgnoreSelected> to
+I<true> the effect of B<Irq> is inversed: All selected interupts are ignored
+and all other interupts are collected.
+
+=back
+
+=head2 Plugin C<mbmon>
+
+=over 4
+
+=item B<Host> I<Hostname>
+
+Hostname to connect to. Defaults to B<127.0.0.1>.
+
+=item B<Port> I<Port>
+
+TCP-Port to connect to. Defaults to B<411>.
+
+=back
+
 =head2 Plugin C<ntpd>
 
 =over 4