2 * collectd - src/barometer.c
4 * This program is free software; you can redistribute it and/or modify it
5 * under the terms of the GNU Lesser General Public License as published by
6 * the Free Software Foundation; only version 2.1 of the License is
9 * This program is distributed in the hope that it will be useful, but
10 * WITHOUT ANY WARRANTY; without even the implied warranty of
11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
12 * Lesser General Public License for more details.
14 * You should have received a copy of the GNU Lesser General Public License
15 * along with this program; if not, write to the Free Software Foundation,
16 * Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
25 #include "utils_cache.h"
31 #include <linux/i2c-dev.h>
34 /* ------------ MPL115 defines ------------ */
35 /* I2C address of the MPL115 sensor */
36 #define MPL115_I2C_ADDRESS 0x60
38 /* register addresses */
39 #define MPL115_ADDR_CONV 0x00
40 #define MPL115_ADDR_COEFFS 0x04
43 #define MPL115_NUM_CONV 4
44 #define MPL115_NUM_COEFFS 12
46 /* commands / addresses */
47 #define MPL115_CMD_CONVERT_PRESS 0x10
48 #define MPL115_CMD_CONVERT_TEMP 0x11
49 #define MPL115_CMD_CONVERT_BOTH 0x12
51 #define MPL115_CONVERSION_RETRIES 5
54 /* ------------ MPL3115 defines ------------ */
55 /* MPL3115 I2C address */
56 #define MPL3115_I2C_ADDRESS 0x60
58 /* register addresses (only the interesting ones) */
59 #define MPL3115_REG_STATUS 0x00
60 #define MPL3115_REG_OUT_P_MSB 0x01
61 #define MPL3115_REG_OUT_P_CSB 0x02
62 #define MPL3115_REG_OUT_P_LSB 0x03
63 #define MPL3115_REG_OUT_T_MSB 0x04
64 #define MPL3115_REG_OUT_T_LSB 0x05
65 #define MPL3115_REG_DR_STATUS 0x06
66 #define MPL3115_REG_WHO_AM_I 0x0C
67 #define MPL3115_REG_SYSMOD 0x11
68 #define MPL3115_REG_PT_DATA_CFG 0x13
69 #define MPL3115_REG_BAR_IN_MSB 0x14
70 #define MPL3115_REG_BAR_IN_LSB 0x15
71 #define MPL3115_REG_CTRL_REG1 0x26
72 #define MPL3115_REG_CTRL_REG2 0x27
73 #define MPL3115_REG_CTRL_REG3 0x28
74 #define MPL3115_REG_CTRL_REG4 0x29
75 #define MPL3115_REG_CTRL_REG5 0x2A
76 #define MPL3115_REG_OFF_P 0x2B
77 #define MPL3115_REG_OFF_T 0x2C
78 #define MPL3115_REG_OFF_H 0x2D
80 /* Register values, masks */
81 #define MPL3115_WHO_AM_I_RESP 0xC4
83 #define MPL3115_PT_DATA_DREM 0x04
84 #define MPL3115_PT_DATA_PDEF 0x02
85 #define MPL3115_PT_DATA_TDEF 0x01
87 #define MPL3115_DR_STATUS_TDR 0x02
88 #define MPL3115_DR_STATUS_PDR 0x04
89 #define MPL3115_DR_STATUS_PTDR 0x08
90 #define MPL3115_DR_STATUS_DR (MPL3115_DR_STATUS_TDR | MPL3115_DR_STATUS_PDR | MPL3115_DR_STATUS_PTDR)
92 #define MPL3115_DR_STATUS_TOW 0x20
93 #define MPL3115_DR_STATUS_POW 0x40
94 #define MPL3115_DR_STATUS_PTOW 0x80
96 #define MPL3115_CTRL_REG1_ALT 0x80
97 #define MPL3115_CTRL_REG1_RAW 0x40
98 #define MPL3115_CTRL_REG1_OST_MASK 0x38
99 #define MPL3115_CTRL_REG1_OST_1 0x00
100 #define MPL3115_CTRL_REG1_OST_2 0x08
101 #define MPL3115_CTRL_REG1_OST_4 0x10
102 #define MPL3115_CTRL_REG1_OST_8 0x18
103 #define MPL3115_CTRL_REG1_OST_16 0x20
104 #define MPL3115_CTRL_REG1_OST_32 0x28
105 #define MPL3115_CTRL_REG1_OST_64 0x30
106 #define MPL3115_CTRL_REG1_OST_128 0x38
107 #define MPL3115_CTRL_REG1_RST 0x04
108 #define MPL3115_CTRL_REG1_OST 0x02
109 #define MPL3115_CTRL_REG1_SBYB 0x01
110 #define MPL3115_CTRL_REG1_SBYB_MASK 0xFE
112 #define MPL3115_NUM_CONV_VALS 5
115 /* ------------ BMP085 defines ------------ */
116 /* I2C address of the BMP085 sensor */
117 #define BMP085_I2C_ADDRESS 0x77
119 /* register addresses */
120 #define BMP085_ADDR_ID_REG 0xD0
121 #define BMP085_ADDR_VERSION 0xD1
123 #define BMP085_ADDR_CONV 0xF6
125 #define BMP085_ADDR_CTRL_REG 0xF4
126 #define BMP085_ADDR_COEFFS 0xAA
129 #define BMP085_NUM_COEFFS 22
131 /* commands, values */
132 #define BMP085_CHIP_ID 0x55
134 #define BMP085_CMD_CONVERT_TEMP 0x2E
136 #define BMP085_CMD_CONVERT_PRESS_0 0x34
137 #define BMP085_CMD_CONVERT_PRESS_1 0x74
138 #define BMP085_CMD_CONVERT_PRESS_2 0xB4
139 #define BMP085_CMD_CONVERT_PRESS_3 0xF4
142 #define BMP085_TIME_CNV_TEMP 4500
144 #define BMP085_TIME_CNV_PRESS_0 4500
145 #define BMP085_TIME_CNV_PRESS_1 7500
146 #define BMP085_TIME_CNV_PRESS_2 13500
147 #define BMP085_TIME_CNV_PRESS_3 25500
150 /* ------------ Normalization ------------ */
151 /* Mean sea level pressure normalization methods */
153 #define MSLP_INTERNATIONAL 1
154 #define MSLP_DEU_WETT 2
156 /** Temperature reference history depth for averaging. See #get_reference_temperature */
157 #define REF_TEMP_AVG_NUM 5
160 /* ------------------------------------------ */
162 /** Supported sensor types */
170 static const char *config_keys[] =
174 "PressureOffset", /**< only for MPL3115 */
175 "TemperatureOffset", /**< only for MPL3115 */
181 static int config_keys_num = STATIC_ARRAY_SIZE(config_keys);
183 static char * config_device = NULL; /**< I2C bus device */
184 static int config_oversample = 1; /**< averaging window */
186 static double config_press_offset = 0.0; /**< pressure offset */
187 static double config_temp_offset = 0.0; /**< temperature offset */
189 static double config_altitude = NAN; /**< altitude */
190 static int config_normalize = 0; /**< normalization method */
192 static _Bool configured = 0; /**< the whole plugin config status */
194 static int i2c_bus_fd = -1; /**< I2C bus device FD */
196 static enum Sensor_type sensor_type = Sensor_none; /**< detected/used sensor type */
198 static __s32 mpl3115_oversample = 0; /**< MPL3115 CTRL1 oversample setting */
200 // BMP085 configuration
201 static unsigned bmp085_oversampling; /**< BMP085 oversampling (0-3) */
202 static unsigned long bmp085_timeCnvPress; /**< BMP085 conversion time for pressure in us */
203 static __u8 bmp085_cmdCnvPress; /**< BMP085 pressure conversion command */
206 /* MPL115 conversion coefficients */
207 static double mpl115_coeffA0;
208 static double mpl115_coeffB1;
209 static double mpl115_coeffB2;
210 static double mpl115_coeffC12;
211 static double mpl115_coeffC11;
212 static double mpl115_coeffC22;
214 /* BMP085 conversion coefficients */
215 static short bmp085_AC1;
216 static short bmp085_AC2;
217 static short bmp085_AC3;
218 static unsigned short bmp085_AC4;
219 static unsigned short bmp085_AC5;
220 static unsigned short bmp085_AC6;
221 static short bmp085_B1;
222 static short bmp085_B2;
223 static short bmp085_MB;
224 static short bmp085_MC;
225 static short bmp085_MD;
229 /* ------------------------ averaging ring buffer ------------------------ */
230 /* Used only for MPL115. MPL3115 supports real oversampling in the device so */
231 /* no need for any postprocessing. */
233 static _Bool avg_initialized = 0; /**< already initialized by real values */
235 typedef struct averaging_s {
236 long int * ring_buffer;
237 int ring_buffer_size;
238 long int ring_buffer_sum;
239 int ring_buffer_head;
243 static averaging_t pressure_averaging = { NULL, 0, 0L, 0 };
244 static averaging_t temperature_averaging = { NULL, 0, 0L, 0 };
248 * Create / allocate averaging buffer
250 * The buffer is initialized with zeros.
252 * @param avg pointer to ring buffer to be allocated
253 * @param size requested buffer size
255 * @return Zero when successful
257 static int averaging_create(averaging_t *avg, int size)
259 avg->ring_buffer = calloc ((size_t) size, sizeof (*avg->ring_buffer));
260 if (avg->ring_buffer == NULL)
262 ERROR ("barometer: averaging_create - ring buffer allocation of size %d failed",
267 avg->ring_buffer_size = size;
268 avg->ring_buffer_sum = 0L;
269 avg->ring_buffer_head = 0;
276 * Delete / free existing averaging buffer
278 * @param avg pointer to the ring buffer to be deleted
280 static void averaging_delete(averaging_t * avg)
282 if (avg->ring_buffer != NULL)
284 free(avg->ring_buffer);
285 avg->ring_buffer = NULL;
287 avg->ring_buffer_size = 0;
288 avg->ring_buffer_sum = 0L;
289 avg->ring_buffer_head = 0;
294 * Add new sample to the averaging buffer
296 * A new averaged value is returned. Note that till the buffer is full
297 * returned value is inaccurate as it is an average of real values and initial
300 * @param avg pointer to the ring buffer
301 * @param sample new sample value
303 * @return Averaged sample value
305 static double averaging_add_sample(averaging_t * avg, long int sample)
309 avg->ring_buffer_sum += sample - avg->ring_buffer[avg->ring_buffer_head];
310 avg->ring_buffer[avg->ring_buffer_head] = sample;
311 avg->ring_buffer_head = (avg->ring_buffer_head+1) % avg->ring_buffer_size;
312 result = (double)(avg->ring_buffer_sum) / (double)(avg->ring_buffer_size);
314 DEBUG ("barometer: averaging_add_sample - added %ld, result = %lf",
322 /* ------------------------ temperature refference ------------------------ */
325 * Linked list type of temperature sensor references
327 typedef struct temperature_list_s {
328 char * sensor_name; /**< sensor name/reference */
329 size_t num_values; /**< number of values (usually one) */
330 _Bool initialized; /**< sensor already provides data */
331 struct temperature_list_s * next; /**< next in the list */
332 } temperature_list_t;
334 static temperature_list_t * temp_list = NULL;
338 * Add new sensor to the temperature reference list
340 * @param list the list
341 * @param sensor reference name (as provided by the config file)
343 * @return Zero when successful
345 static int temp_list_add(temperature_list_t * list, const char * sensor)
347 temperature_list_t *new_temp;
349 new_temp = malloc(sizeof (*new_temp));
353 new_temp->sensor_name = strdup(sensor);
354 new_temp->initialized = 0;
355 new_temp->num_values = 0;
356 if(new_temp->sensor_name == NULL)
362 new_temp->next = temp_list;
363 temp_list = new_temp;
369 * Delete the whole temperature reference list
371 * @param list the list to be deleted
373 static void temp_list_delete(temperature_list_t ** list)
375 temperature_list_t * tmp;
377 while (*list != NULL)
380 (*list) = (*list)->next;
381 free(tmp->sensor_name);
389 * Get reference temperature value
391 * First initially uc_get_rate_by_name is tried. At the startup due to nondeterministic
392 * order the temperature may not be read yet (then it fails and first measurment gives
393 * only absolute air pressure reading which is acceptable). Once it succedes (should be
394 * second measurement at the latest) we use average of few last readings from
395 * uc_get_history_by_name. It may take few readings to start filling so again we use
396 * uc_get_rate_by_name as a fallback.
397 * The idea is to use basic "noise" filtering (history averaging) across all the values
398 * which given sensor provides (up to given depth). Then we get minimum among
401 * @param result where the result is stored. When not available NAN is stored.
403 * @return Zero when successful
405 static int get_reference_temperature(double * result)
407 temperature_list_t * list = temp_list;
409 gauge_t * values = NULL; /**< rate values */
410 size_t values_num = 0; /**< number of rate values */
412 gauge_t values_history[REF_TEMP_AVG_NUM];
414 double avg_sum; /**< Value sum for computing average */
415 int avg_num; /**< Number of values for computing average */
416 double average; /**< Resulting value average */
425 /* First time need to read current rate to learn how many values are
426 there (typically for temperature it would be just one).
427 We do not expect dynamic changing of number of temperarure values
428 in runtime yet (are there any such cases?). */
429 if(!list->initialized)
431 if(uc_get_rate_by_name(list->sensor_name,
435 DEBUG ("barometer: get_reference_temperature - rate \"%s\" not found yet",
441 DEBUG ("barometer: get_reference_temperature - initialize \"%s\", %zu vals",
445 list->initialized = 1;
446 list->num_values = values_num;
448 for(size_t i=0; i<values_num; ++i)
450 DEBUG ("barometer: get_reference_temperature - rate %zu: %lf **",
452 if(!isnan(values[i]))
454 avg_sum += values[i];
462 /* It is OK to get here the first time as well, in the worst case
463 the history will full of NANs. */
464 if(uc_get_history_by_name(list->sensor_name,
469 ERROR ("barometer: get_reference_temperature - history \"%s\" lost",
471 list->initialized = 0;
472 list->num_values = 0;
477 for(size_t i=0; i<REF_TEMP_AVG_NUM*list->num_values; ++i)
479 DEBUG ("barometer: get_reference_temperature - history %zu: %lf",
480 i, values_history[i]);
481 if(!isnan(values_history[i]))
483 avg_sum += values_history[i];
488 if(avg_num == 0) /* still no history? fallback to current */
490 if(uc_get_rate_by_name(list->sensor_name,
494 ERROR ("barometer: get_reference_temperature - rate \"%s\" lost",
496 list->initialized = 0;
497 list->num_values = 0;
502 for(size_t i=0; i<values_num; ++i)
504 DEBUG ("barometer: get_reference_temperature - rate last %zu: %lf **",
506 if(!isnan(values[i]))
508 avg_sum += values[i];
518 ERROR ("barometer: get_reference_temperature - could not read \"%s\"",
520 list->initialized = 0;
521 list->num_values = 0;
525 average = avg_sum / (double) avg_num;
528 else if(*result>average)
532 } /* while sensor list */
536 ERROR("barometer: get_reference_temperature - no sensor available (yet?)");
539 DEBUG ("barometer: get_reference_temperature - temp is %lf", *result);
544 /* ------------------------ MPL115 access ------------------------ */
547 * Detect presence of a MPL115 pressure sensor.
549 * Unfortunately there seems to be no ID register so we just try to read first
550 * conversion coefficient from device at MPL115 address and hope it is really
551 * MPL115. We should use this check as the last resort (which would be the typical
552 * case anyway since MPL115 is the least accurate sensor).
553 * As a sideeffect will leave set I2C slave address.
555 * @return 1 if MPL115, 0 otherwise
557 static int MPL115_detect(void)
562 if (ioctl(i2c_bus_fd, I2C_SLAVE_FORCE, MPL115_I2C_ADDRESS) < 0)
564 ERROR("barometer: MPL115_detect problem setting i2c slave address to 0x%02X: %s",
566 sstrerror (errno, errbuf, sizeof (errbuf)));
570 res = i2c_smbus_read_byte_data(i2c_bus_fd, MPL115_ADDR_COEFFS);
573 DEBUG ("barometer: MPL115_detect - positive detection");
577 DEBUG ("barometer: MPL115_detect - negative detection");
582 * Read the MPL115 sensor conversion coefficients.
584 * These are (device specific) constants so we can read them just once.
586 * @return Zero when successful
588 static int MPL115_read_coeffs(void)
590 uint8_t mpl115_coeffs[MPL115_NUM_COEFFS] = { 0 };
593 int8_t sia0MSB, sia0LSB, sib1MSB, sib1LSB, sib2MSB, sib2LSB;
594 int8_t sic12MSB, sic12LSB, sic11MSB, sic11LSB, sic22MSB, sic22LSB;
595 int16_t sia0, sib1, sib2, sic12, sic11, sic22;
599 res = i2c_smbus_read_i2c_block_data(i2c_bus_fd,
601 STATIC_ARRAY_SIZE (mpl115_coeffs),
605 ERROR ("barometer: MPL115_read_coeffs - problem reading data: %s",
606 sstrerror (errno, errbuf, sizeof (errbuf)));
610 /* Using perhaps less elegant/efficient code, but more readable. */
611 /* a0: 16total 1sign 12int 4fract 0pad */
612 sia0MSB = mpl115_coeffs[0];
613 sia0LSB = mpl115_coeffs[1];
614 sia0 = (int16_t) sia0MSB <<8; /* s16 type, Shift to MSB */
615 sia0 += (int16_t) sia0LSB & 0x00FF; /* Add LSB to 16bit number */
616 mpl115_coeffA0 = (double) (sia0);
617 mpl115_coeffA0 /= 8.0; /* 3 fract bits */
619 /* b1: 16total 1sign 2int 13fract 0pad */
620 sib1MSB= mpl115_coeffs[2];
621 sib1LSB= mpl115_coeffs[3];
622 sib1 = sib1MSB <<8; /* Shift to MSB */
623 sib1 += sib1LSB & 0x00FF; /* Add LSB to 16bit number */
624 mpl115_coeffB1 = (double) (sib1);
625 mpl115_coeffB1 /= 8192.0; /* 13 fract */
627 /* b2: 16total 1sign 1int 14fract 0pad */
628 sib2MSB= mpl115_coeffs[4];
629 sib2LSB= mpl115_coeffs[5];
630 sib2 = sib2MSB <<8; /* Shift to MSB */
631 sib2 += sib2LSB & 0x00FF; /* Add LSB to 16bit number */
632 mpl115_coeffB2 = (double) (sib2);
633 mpl115_coeffB2 /= 16384.0; /* 14 fract */
635 /* c12: 14total 1sign 0int 13fract 9pad */
636 sic12MSB= mpl115_coeffs[6];
637 sic12LSB= mpl115_coeffs[7];
638 sic12 = sic12MSB <<8; /* Shift to MSB only by 8 for MSB */
639 sic12 += sic12LSB & 0x00FF;
640 mpl115_coeffC12 = (double) (sic12);
641 mpl115_coeffC12 /= 4.0; /* 16-14=2 */
642 mpl115_coeffC12 /= 4194304.0; /* 13+9=22 fract */
644 /* c11: 11total 1sign 0int 11fract 11pad */
645 sic11MSB= mpl115_coeffs[8];
646 sic11LSB= mpl115_coeffs[9];
647 sic11 = sic11MSB <<8; /* Shift to MSB only by 8 for MSB */
648 sic11 += sic11LSB & 0x00FF;
649 mpl115_coeffC11 = (double) (sic11);
650 mpl115_coeffC11 /= 32.0; /* 16-11=5 */
651 mpl115_coeffC11 /= 4194304.0; /* 11+11=22 fract */
653 /* c12: 11total 1sign 0int 10fract 15pad */
654 sic22MSB= mpl115_coeffs[10];
655 sic22LSB= mpl115_coeffs[11];
656 sic22 = sic22MSB <<8; /* Shift to MSB only by 8 for MSB */
657 sic22 += sic22LSB & 0x00FF;
658 mpl115_coeffC22 = (double) (sic22);
659 mpl115_coeffC22 /= 32.0; //16-11=5
660 mpl115_coeffC22 /= 33554432.0; /* 10+15=25 fract */
662 DEBUG("barometer: MPL115_read_coeffs: a0=%lf, b1=%lf, b2=%lf, c12=%lf, c11=%lf, c22=%lf",
674 * Convert raw adc values to real data using the sensor coefficients.
676 * @param adc_pressure adc pressure value to be converted
677 * @param adc_temp adc temperature value to be converted
678 * @param pressure computed real pressure
679 * @param temperature computed real temperature
681 static void MPL115_convert_adc_to_real(double adc_pressure,
684 double * temperature)
687 Pcomp = mpl115_coeffA0 + \
688 (mpl115_coeffB1 + mpl115_coeffC11*adc_pressure + mpl115_coeffC12*adc_temp) * adc_pressure + \
689 (mpl115_coeffB2 + mpl115_coeffC22*adc_temp) * adc_temp;
691 *pressure = ((1150.0-500.0) * Pcomp / 1023.0) + 500.0;
692 *temperature = (472.0 - adc_temp) / 5.35 + 25.0;
693 DEBUG ("barometer: MPL115_convert_adc_to_real - got %lf hPa, %lf C",
700 * Read sensor averegaed measurements
702 * @param pressure averaged measured pressure
703 * @param temperature averaged measured temperature
705 * @return Zero when successful
707 static int MPL115_read_averaged(double * pressure, double * temperature)
709 uint8_t mpl115_conv[MPL115_NUM_CONV] = { 0 };
713 int conv_temperature;
715 double adc_temperature;
721 /* start conversion of both temp and presure */
722 retries = MPL115_CONVERSION_RETRIES;
725 /* write 1 to start conversion */
726 res = i2c_smbus_write_byte_data (i2c_bus_fd,
727 MPL115_CMD_CONVERT_BOTH,
735 ERROR ("barometer: MPL115_read_averaged - requesting conversion: %s, " \
736 "will retry at most %d more times",
737 sstrerror (errno, errbuf, sizeof (errbuf)),
742 ERROR ("barometer: MPL115_read_averaged - requesting conversion: %s, "\
743 "too many failed retries",
744 sstrerror (errno, errbuf, sizeof (errbuf)));
749 usleep (10000); /* wait 10ms for the conversion */
751 retries=MPL115_CONVERSION_RETRIES;
754 res = i2c_smbus_read_i2c_block_data(i2c_bus_fd,
756 STATIC_ARRAY_SIZE (mpl115_conv),
764 ERROR ("barometer: MPL115_read_averaged - reading conversion: %s, " \
765 "will retry at most %d more times",
766 sstrerror (errno, errbuf, sizeof (errbuf)),
771 ERROR ("barometer: MPL115_read_averaged - reading conversion: %s, " \
772 "too many failed retries",
773 sstrerror (errno, errbuf, sizeof (errbuf)));
778 conv_pressure = ((mpl115_conv[0] << 8) | mpl115_conv[1]) >> 6;
779 conv_temperature = ((mpl115_conv[2] << 8) | mpl115_conv[3]) >> 6;
780 DEBUG ("barometer: MPL115_read_averaged, raw pressure ADC value = %d, " \
781 "raw temperature ADC value = %d",
785 adc_pressure = averaging_add_sample (&pressure_averaging, conv_pressure);
786 adc_temperature = averaging_add_sample (&temperature_averaging, conv_temperature);
788 MPL115_convert_adc_to_real(adc_pressure, adc_temperature, pressure, temperature);
790 DEBUG ("barometer: MPL115_read_averaged - averaged ADC pressure = %lf / temperature = %lf, " \
791 "real pressure = %lf hPa / temperature = %lf C",
800 /* ------------------------ MPL3115 access ------------------------ */
803 * Detect presence of a MPL3115 pressure sensor by checking register "WHO AM I"
805 * As a sideeffect will leave set I2C slave address.
807 * @return 1 if MPL3115, 0 otherwise
809 static int MPL3115_detect(void)
814 if (ioctl(i2c_bus_fd, I2C_SLAVE_FORCE, MPL3115_I2C_ADDRESS) < 0)
816 ERROR("barometer: MPL3115_detect problem setting i2c slave address to 0x%02X: %s",
818 sstrerror (errno, errbuf, sizeof (errbuf)));
822 res = i2c_smbus_read_byte_data(i2c_bus_fd, MPL3115_REG_WHO_AM_I);
823 if(res == MPL3115_WHO_AM_I_RESP)
825 DEBUG ("barometer: MPL3115_detect - positive detection");
829 DEBUG ("barometer: MPL3115_detect - negative detection");
834 * Adjusts oversampling to values supported by MPL3115
836 * MPL3115 supports only power of 2 in the range 1 to 128.
838 static void MPL3115_adjust_oversampling(void)
842 if(config_oversample > 100)
845 mpl3115_oversample = MPL3115_CTRL_REG1_OST_128;
847 else if(config_oversample > 48)
850 mpl3115_oversample = MPL3115_CTRL_REG1_OST_64;
852 else if(config_oversample > 24)
855 mpl3115_oversample = MPL3115_CTRL_REG1_OST_32;
857 else if(config_oversample > 12)
860 mpl3115_oversample = MPL3115_CTRL_REG1_OST_16;
862 else if(config_oversample > 6)
865 mpl3115_oversample = MPL3115_CTRL_REG1_OST_8;
867 else if(config_oversample > 3)
870 mpl3115_oversample = MPL3115_CTRL_REG1_OST_4;
872 else if(config_oversample > 1)
875 mpl3115_oversample = MPL3115_CTRL_REG1_OST_2;
880 mpl3115_oversample = MPL3115_CTRL_REG1_OST_1;
883 DEBUG("barometer: MPL3115_adjust_oversampling - correcting oversampling from %d to %d",
886 config_oversample = new_val;
890 * Read sensor averaged measurements
892 * @param pressure averaged measured pressure
893 * @param temperature averaged measured temperature
895 * @return Zero when successful
897 static int MPL3115_read(double * pressure, double * temperature)
901 __u8 data[MPL3115_NUM_CONV_VALS];
902 long int tmp_value = 0;
905 /* Set Active - activate the device from standby */
906 res = i2c_smbus_read_byte_data(i2c_bus_fd, MPL3115_REG_CTRL_REG1);
909 ERROR ("barometer: MPL3115_read - cannot read CTRL_REG1: %s",
910 sstrerror (errno, errbuf, sizeof (errbuf)));
914 res = i2c_smbus_write_byte_data(i2c_bus_fd,
915 MPL3115_REG_CTRL_REG1,
916 ctrl | MPL3115_CTRL_REG1_SBYB);
919 ERROR ("barometer: MPL3115_read - problem activating: %s",
920 sstrerror (errno, errbuf, sizeof (errbuf)));
924 /* base sleep is 5ms x OST */
925 usleep(5000 * config_oversample);
927 /* check the flags/status if ready */
928 res = i2c_smbus_read_byte_data(i2c_bus_fd, MPL3115_REG_STATUS);
931 ERROR ("barometer: MPL3115_read - cannot read status register: %s",
932 sstrerror (errno, errbuf, sizeof (errbuf)));
936 while ((res & MPL3115_DR_STATUS_DR) != MPL3115_DR_STATUS_DR)
938 /* try some extra sleep... */
941 /* ... and repeat the check. The conversion has to finish sooner or later. */
942 res = i2c_smbus_read_byte_data(i2c_bus_fd, MPL3115_REG_STATUS);
945 ERROR ("barometer: MPL3115_read - cannot read status register: %s",
946 sstrerror (errno, errbuf, sizeof (errbuf)));
951 /* Now read all the data in one block. There is address autoincrement. */
952 res = i2c_smbus_read_i2c_block_data(i2c_bus_fd,
953 MPL3115_REG_OUT_P_MSB,
954 MPL3115_NUM_CONV_VALS,
958 ERROR ("barometer: MPL3115_read - cannot read data registers: %s",
959 sstrerror (errno, errbuf, sizeof (errbuf)));
963 tmp_value = (data[0] << 16) | (data[1] << 8) | data[2];
964 *pressure = ((double) tmp_value) / 4.0 / 16.0 / 100.0;
965 DEBUG ("barometer: MPL3115_read - absolute pressure = %lf hPa", *pressure);
969 data[3] = ~data[3] + 1;
970 *temperature = data[3];
971 *temperature = - *temperature;
975 *temperature = data[3];
978 *temperature += (double)(data[4]) / 256.0;
979 DEBUG ("barometer: MPL3115_read - temperature = %lf C", *temperature);
985 * Initialize MPL3115 for barometeric measurements
987 * @return 0 if successful
989 static int MPL3115_init_sensor(void)
995 /* Reset the sensor. It will reset immediately without ACKing */
996 /* the transaction, so no error handling here. */
997 i2c_smbus_write_byte_data(i2c_bus_fd,
998 MPL3115_REG_CTRL_REG1,
999 MPL3115_CTRL_REG1_RST);
1001 /* wait some time for the reset to finish */
1004 /* now it should be in standby already so we can go and configure it */
1006 /* Set temperature offset. */
1007 /* result = ADCtemp + offset [C] */
1008 offset = (__s8) (config_temp_offset * 16.0);
1009 res = i2c_smbus_write_byte_data(i2c_bus_fd, MPL3115_REG_OFF_T, offset);
1012 ERROR ("barometer: MPL3115_init_sensor - problem setting temp offset: %s",
1013 sstrerror (errno, errbuf, sizeof (errbuf)));
1017 /* Set pressure offset. */
1018 /* result = ADCpress + offset [hPa] */
1019 offset = (__s8) (config_press_offset * 100.0 / 4.0);
1020 res = i2c_smbus_write_byte_data(i2c_bus_fd, MPL3115_REG_OFF_P, offset);
1023 ERROR ("barometer: MPL3115_init_sensor - problem setting pressure offset: %s",
1024 sstrerror (errno, errbuf, sizeof (errbuf)));
1028 /* Enable Data Flags in PT_DATA_CFG - flags on both pressure and temp */
1029 res = i2c_smbus_write_byte_data(i2c_bus_fd,
1030 MPL3115_REG_PT_DATA_CFG,
1031 MPL3115_PT_DATA_DREM \
1032 | MPL3115_PT_DATA_PDEF \
1033 | MPL3115_PT_DATA_TDEF);
1036 ERROR ("barometer: MPL3115_init_sensor - problem setting PT_DATA_CFG: %s",
1037 sstrerror (errno, errbuf, sizeof (errbuf)));
1041 /* Set to barometer with an OSR */
1042 res = i2c_smbus_write_byte_data(i2c_bus_fd,
1043 MPL3115_REG_CTRL_REG1,
1044 mpl3115_oversample);
1047 ERROR ("barometer: MPL3115_init_sensor - problem configuring CTRL_REG1: %s",
1048 sstrerror (errno, errbuf, sizeof (errbuf)));
1055 /* ------------------------ BMP085 access ------------------------ */
1058 * Detect presence of a BMP085 pressure sensor by checking its ID register
1060 * As a sideeffect will leave set I2C slave address.
1062 * @return 1 if BMP085, 0 otherwise
1064 static int BMP085_detect(void)
1069 if (ioctl(i2c_bus_fd, I2C_SLAVE_FORCE, BMP085_I2C_ADDRESS) < 0)
1071 ERROR("barometer: BMP085_detect - problem setting i2c slave address to 0x%02X: %s",
1073 sstrerror (errno, errbuf, sizeof (errbuf)));
1077 res = i2c_smbus_read_byte_data(i2c_bus_fd, BMP085_ADDR_ID_REG);
1078 if(res == BMP085_CHIP_ID)
1080 DEBUG ("barometer: BMP085_detect - positive detection");
1083 res = i2c_smbus_read_byte_data(i2c_bus_fd, BMP085_ADDR_VERSION );
1086 ERROR("barometer: BMP085_detect - problem checking chip version: %s",
1087 sstrerror (errno, errbuf, sizeof (errbuf)));
1090 DEBUG ("barometer: BMP085_detect - chip version ML:0x%02X AL:0x%02X",
1096 DEBUG ("barometer: BMP085_detect - negative detection");
1102 * Adjusts oversampling settings to values supported by BMP085
1104 * BMP085 supports only 1,2,4 or 8 samples.
1106 static void BMP085_adjust_oversampling(void)
1110 if( config_oversample > 6 ) /* 8 */
1113 bmp085_oversampling = 3;
1114 bmp085_cmdCnvPress = BMP085_CMD_CONVERT_PRESS_3;
1115 bmp085_timeCnvPress = BMP085_TIME_CNV_PRESS_3;
1117 else if( config_oversample > 3 ) /* 4 */
1120 bmp085_oversampling = 2;
1121 bmp085_cmdCnvPress = BMP085_CMD_CONVERT_PRESS_2;
1122 bmp085_timeCnvPress = BMP085_TIME_CNV_PRESS_2;
1124 else if( config_oversample > 1 ) /* 2 */
1127 bmp085_oversampling = 1;
1128 bmp085_cmdCnvPress = BMP085_CMD_CONVERT_PRESS_1;
1129 bmp085_timeCnvPress = BMP085_TIME_CNV_PRESS_1;
1134 bmp085_oversampling = 0;
1135 bmp085_cmdCnvPress = BMP085_CMD_CONVERT_PRESS_0;
1136 bmp085_timeCnvPress = BMP085_TIME_CNV_PRESS_0;
1139 DEBUG("barometer: BMP085_adjust_oversampling - correcting oversampling from %d to %d",
1142 config_oversample = new_val;
1147 * Read the BMP085 sensor conversion coefficients.
1149 * These are (device specific) constants so we can read them just once.
1151 * @return Zero when successful
1153 static int BMP085_read_coeffs(void)
1156 __u8 coeffs[BMP085_NUM_COEFFS];
1159 res = i2c_smbus_read_i2c_block_data(i2c_bus_fd,
1165 ERROR ("barometer: BMP085_read_coeffs - problem reading data: %s",
1166 sstrerror (errno, errbuf, sizeof (errbuf)));
1170 bmp085_AC1 = ((int16_t) coeffs[0] <<8) | (int16_t) coeffs[1];
1171 bmp085_AC2 = ((int16_t) coeffs[2] <<8) | (int16_t) coeffs[3];
1172 bmp085_AC3 = ((int16_t) coeffs[4] <<8) | (int16_t) coeffs[5];
1173 bmp085_AC4 = ((uint16_t) coeffs[6] <<8) | (uint16_t) coeffs[7];
1174 bmp085_AC5 = ((uint16_t) coeffs[8] <<8) | (uint16_t) coeffs[9];
1175 bmp085_AC6 = ((uint16_t) coeffs[10] <<8) | (uint16_t) coeffs[11];
1176 bmp085_B1 = ((int16_t) coeffs[12] <<8) | (int16_t) coeffs[13];
1177 bmp085_B2 = ((int16_t) coeffs[14] <<8) | (int16_t) coeffs[15];
1178 bmp085_MB = ((int16_t) coeffs[16] <<8) | (int16_t) coeffs[17];
1179 bmp085_MC = ((int16_t) coeffs[18] <<8) | (int16_t) coeffs[19];
1180 bmp085_MD = ((int16_t) coeffs[20] <<8) | (int16_t) coeffs[21];
1182 DEBUG("barometer: BMP085_read_coeffs - AC1=%d, AC2=%d, AC3=%d, AC4=%u,"\
1183 " AC5=%u, AC6=%u, B1=%d, B2=%d, MB=%d, MC=%d, MD=%d",
1201 * Convert raw BMP085 adc values to real data using the sensor coefficients.
1203 * @param adc_pressure adc pressure value to be converted
1204 * @param adc_temp adc temperature value to be converted
1205 * @param pressure computed real pressure
1206 * @param temperature computed real temperature
1208 static void BMP085_convert_adc_to_real(long adc_pressure,
1209 long adc_temperature,
1211 double * temperature)
1216 unsigned long B4, B7;
1222 /* calculate real temperature */
1223 X1 = ( (adc_temperature - bmp085_AC6) * bmp085_AC5) >> 15;
1224 X2 = (bmp085_MC << 11) / (X1 + bmp085_MD);
1229 *temperature = (double)T * 0.1;
1231 /* calculate real pressure */
1232 /* in general X1, X2, X3 are recycled while values of B3, B4, B5, B6 are kept */
1236 X1 = ((bmp085_B2 * ((B6 * B6)>>12)) >> 11 );
1237 X2 = (((long)bmp085_AC2 * B6) >> 11);
1239 B3 = (((((long)bmp085_AC1 * 4) + X3) << bmp085_oversampling) + 2) >> 2;
1242 X1 = (((long)bmp085_AC3*B6) >> 13);
1243 X2 = (bmp085_B1*((B6*B6) >> 12) ) >> 16;
1244 X3 = ((X1 + X2) + 2 ) >> 2;
1245 B4 = ((long)bmp085_AC4* (unsigned long)(X3 + 32768)) >> 15;
1248 B7 = (unsigned long)(adc_pressure - B3)*(50000>>bmp085_oversampling);
1249 if( B7 < 0x80000000 )
1257 X1 = (P >> 8) * (P >> 8);
1258 X1 = (X1 * 3038) >> 16;
1259 X2 = ((-7357) * P) >> 16;
1260 P = P + ( ( X1 + X2 + 3791 ) >> 4);
1262 *pressure = P / 100.0; // in [hPa]
1263 DEBUG ("barometer: BMP085_convert_adc_to_real - got %lf hPa, %lf C",
1270 * Read compensated sensor measurements
1272 * @param pressure averaged measured pressure
1273 * @param temperature averaged measured temperature
1275 * @return Zero when successful
1277 static int BMP085_read(double * pressure, double * temperature)
1283 long adc_temperature;
1287 /* start conversion of temperature */
1288 res = i2c_smbus_write_byte_data( i2c_bus_fd,
1289 BMP085_ADDR_CTRL_REG,
1290 BMP085_CMD_CONVERT_TEMP );
1293 ERROR ("barometer: BMP085_read - problem requesting temperature conversion: %s",
1294 sstrerror (errno, errbuf, sizeof (errbuf)));
1298 usleep(BMP085_TIME_CNV_TEMP); /* wait for the conversion */
1300 res = i2c_smbus_read_i2c_block_data( i2c_bus_fd,
1306 ERROR ("barometer: BMP085_read - problem reading temperature data: %s",
1307 sstrerror (errno, errbuf, sizeof (errbuf)));
1311 adc_temperature = ( (unsigned short)measBuff[0] << 8 ) + measBuff[1];
1315 res = i2c_smbus_write_byte_data( i2c_bus_fd,
1316 BMP085_ADDR_CTRL_REG,
1317 bmp085_cmdCnvPress );
1320 ERROR ("barometer: BMP085_read - problem requesting pressure conversion: %s",
1321 sstrerror (errno, errbuf, sizeof (errbuf)));
1325 usleep(bmp085_timeCnvPress); /* wait for the conversion */
1327 res = i2c_smbus_read_i2c_block_data( i2c_bus_fd,
1333 ERROR ("barometer: BMP085_read - problem reading pressure data: %s",
1334 sstrerror (errno, errbuf, sizeof (errbuf)));
1338 adc_pressure = (long)((((ulong)measBuff[0]<<16) | ((ulong)measBuff[1]<<8) | (ulong)measBuff[2] ) >> (8 - bmp085_oversampling));
1341 DEBUG ("barometer: BMP085_read - raw pressure ADC value = %ld, " \
1342 "raw temperature ADC value = %ld",
1346 BMP085_convert_adc_to_real(adc_pressure, adc_temperature, pressure, temperature);
1353 /* ------------------------ Sensor detection ------------------------ */
1355 * Detect presence of a supported sensor.
1357 * As a sideeffect will leave set I2C slave address.
1358 * The detection is done in the order BMP085, MPL3115, MPL115 and stops after
1359 * first sensor beeing found.
1361 * @return detected sensor type
1363 static enum Sensor_type detect_sensor_type(void)
1366 return Sensor_BMP085;
1368 else if(MPL3115_detect())
1369 return Sensor_MPL3115;
1371 else if(MPL115_detect())
1372 return Sensor_MPL115;
1377 /* ------------------------ Common functionality ------------------------ */
1380 * Convert absolute pressure (in hPa) to mean sea level pressure
1382 * Implemented methods are:
1383 * - MSLP_NONE - no converions, returns absolute pressure
1385 * - MSLP_INTERNATIONAL - see http://en.wikipedia.org/wiki/Atmospheric_pressure#Altitude_atmospheric_pressure_variation
1386 * Requires #config_altitude
1388 * - MSLP_DEU_WETT - formula as recommended by the Deutsche Wetterdienst. See
1389 * http://de.wikipedia.org/wiki/Barometrische_H%C3%B6henformel#Theorie
1390 * Requires both #config_altitude and temperature reference(s).
1392 * @param abs_pressure absloute pressure to be converted
1394 * @return mean sea level pressure if successful, NAN otherwise
1396 static double abs_to_mean_sea_level_pressure(double abs_pressure)
1402 if (config_normalize >= MSLP_DEU_WETT)
1404 result = get_reference_temperature(&temp);
1411 switch(config_normalize)
1414 mean = abs_pressure;
1417 case MSLP_INTERNATIONAL:
1418 mean = abs_pressure / \
1419 pow(1.0 - 0.0065*config_altitude/288.15, 9.80665*0.0289644/(8.31447*0.0065));
1424 double E; /* humidity */
1427 E = 5.6402 * (-0.0916 + exp(0.06*temp) );
1429 E = 18.2194 * (1.0463 - exp(-0.0666*temp) );
1430 x = 9.80665 / (287.05 * (temp+273.15 + 0.12*E + 0.0065*config_altitude/2)) * config_altitude;
1431 mean = abs_pressure * exp(x);
1436 ERROR ("barometer: abs_to_mean_sea_level_pressure: wrong conversion method %d",
1438 mean = abs_pressure;
1442 DEBUG ("barometer: abs_to_mean_sea_level_pressure: absPressure = %lf hPa, method = %d, meanPressure = %lf hPa",
1450 /* ------------------------ main plugin callbacks ------------------------ */
1453 * Main plugin configuration callback (using simple config)
1455 * @param key configuration key we should process
1456 * @param value configuration value we should process
1458 * @return Zero when successful.
1460 static int collectd_barometer_config (const char *key, const char *value)
1462 DEBUG("barometer: collectd_barometer_config");
1464 if (strcasecmp (key, "Device") == 0)
1466 sfree (config_device);
1467 config_device = strdup (value);
1469 else if (strcasecmp (key, "Oversampling") == 0)
1471 int oversampling_tmp = atoi (value);
1472 if (oversampling_tmp < 1 || oversampling_tmp > 1024)
1474 WARNING ("barometer: collectd_barometer_config: invalid oversampling: %d." \
1475 " Allowed values are 1 to 1024 (for MPL115) or 1 to 128 (for MPL3115) or 1 to 8 (for BMP085).",
1479 config_oversample = oversampling_tmp;
1481 else if (strcasecmp (key, "Altitude") == 0)
1483 config_altitude = atof (value);
1485 else if (strcasecmp (key, "Normalization") == 0)
1487 int normalize_tmp = atoi (value);
1488 if (normalize_tmp < 0 || normalize_tmp > 2)
1490 WARNING ("barometer: collectd_barometer_config: invalid normalization: %d",
1494 config_normalize = normalize_tmp;
1496 else if (strcasecmp (key, "TemperatureSensor") == 0)
1498 if(temp_list_add(temp_list, value))
1503 else if (strcasecmp (key, "PressureOffset") == 0)
1505 config_press_offset = atof(value);
1507 else if (strcasecmp (key, "TemperatureOffset") == 0)
1509 config_temp_offset = atof(value);
1521 * Shutdown callback.
1523 * Close I2C and delete all the buffers.
1525 * @return Zero when successful (at the moment the only possible outcome)
1527 static int collectd_barometer_shutdown(void)
1529 DEBUG ("barometer: collectd_barometer_shutdown");
1531 if(sensor_type == Sensor_MPL115)
1533 averaging_delete (&pressure_averaging);
1534 averaging_delete (&temperature_averaging);
1536 temp_list_delete(&temp_list);
1543 sfree (config_device);
1551 * Plugin read callback for MPL115.
1553 * Dispatching will create values:
1554 * - <hostname>/barometer-mpl115/pressure-normalized
1555 * - <hostname>/barometer-mpl115/pressure-absolute
1556 * - <hostname>/barometer-mpl115/temperature
1558 * @return Zero when successful.
1560 static int MPL115_collectd_barometer_read (void)
1564 double pressure = 0.0;
1565 double temperature = 0.0;
1566 double norm_pressure = 0.0;
1568 value_list_t vl = VALUE_LIST_INIT;
1571 DEBUG("barometer: MPL115_collectd_barometer_read");
1578 /* Rather than delaying init, we will intitialize during first read. This
1579 way at least we have a better chance to have the reference temperature
1580 already available. */
1581 if(!avg_initialized)
1583 for(int i=0; i<config_oversample-1; ++i)
1585 result = MPL115_read_averaged(&pressure, &temperature);
1588 ERROR ("barometer: MPL115_collectd_barometer_read - mpl115 read, ignored during init");
1590 DEBUG("barometer: MPL115_collectd_barometer_read - init %d / %d", i+1, config_oversample-1);
1593 avg_initialized = 1;
1596 result = MPL115_read_averaged(&pressure, &temperature);
1600 norm_pressure = abs_to_mean_sea_level_pressure(pressure);
1602 sstrncpy (vl.host, hostname_g, sizeof (vl.host));
1603 sstrncpy (vl.plugin, "barometer", sizeof (vl.plugin));
1604 sstrncpy (vl.plugin_instance, "mpl115", sizeof (vl.plugin_instance));
1609 /* dispatch normalized air pressure */
1610 sstrncpy (vl.type, "pressure", sizeof (vl.type));
1611 sstrncpy (vl.type_instance, "normalized", sizeof (vl.type_instance));
1612 values[0].gauge = norm_pressure;
1613 plugin_dispatch_values (&vl);
1615 /* dispatch absolute air pressure */
1616 sstrncpy (vl.type, "pressure", sizeof (vl.type));
1617 sstrncpy (vl.type_instance, "absolute", sizeof (vl.type_instance));
1618 values[0].gauge = pressure;
1619 plugin_dispatch_values (&vl);
1621 /* dispatch sensor temperature */
1622 sstrncpy (vl.type, "temperature", sizeof (vl.type));
1623 sstrncpy (vl.type_instance, "", sizeof (vl.type_instance));
1624 values[0].gauge = temperature;
1625 plugin_dispatch_values (&vl);
1632 * Plugin read callback for MPL3115.
1634 * Dispatching will create values:
1635 * - <hostname>/barometer-mpl3115/pressure-normalized
1636 * - <hostname>/barometer-mpl3115/pressure-absolute
1637 * - <hostname>/barometer-mpl3115/temperature
1639 * @return Zero when successful.
1641 static int MPL3115_collectd_barometer_read (void)
1645 double pressure = 0.0;
1646 double temperature = 0.0;
1647 double norm_pressure = 0.0;
1649 value_list_t vl = VALUE_LIST_INIT;
1652 DEBUG("barometer: MPL3115_collectd_barometer_read");
1659 result = MPL3115_read(&pressure, &temperature);
1663 norm_pressure = abs_to_mean_sea_level_pressure(pressure);
1665 sstrncpy (vl.host, hostname_g, sizeof (vl.host));
1666 sstrncpy (vl.plugin, "barometer", sizeof (vl.plugin));
1667 sstrncpy (vl.plugin_instance, "mpl3115", sizeof (vl.plugin_instance));
1672 /* dispatch normalized air pressure */
1673 sstrncpy (vl.type, "pressure", sizeof (vl.type));
1674 sstrncpy (vl.type_instance, "normalized", sizeof (vl.type_instance));
1675 values[0].gauge = norm_pressure;
1676 plugin_dispatch_values (&vl);
1678 /* dispatch absolute air pressure */
1679 sstrncpy (vl.type, "pressure", sizeof (vl.type));
1680 sstrncpy (vl.type_instance, "absolute", sizeof (vl.type_instance));
1681 values[0].gauge = pressure;
1682 plugin_dispatch_values (&vl);
1684 /* dispatch sensor temperature */
1685 sstrncpy (vl.type, "temperature", sizeof (vl.type));
1686 sstrncpy (vl.type_instance, "", sizeof (vl.type_instance));
1687 values[0].gauge = temperature;
1688 plugin_dispatch_values (&vl);
1695 * Plugin read callback for BMP085.
1697 * Dispatching will create values:
1698 * - <hostname>/barometer-bmp085/pressure-normalized
1699 * - <hostname>/barometer-bmp085/pressure-absolute
1700 * - <hostname>/barometer-bmp085/temperature
1702 * @return Zero when successful.
1704 static int BMP085_collectd_barometer_read (void)
1708 double pressure = 0.0;
1709 double temperature = 0.0;
1710 double norm_pressure = 0.0;
1712 value_list_t vl = VALUE_LIST_INIT;
1715 DEBUG("barometer: BMP085_collectd_barometer_read");
1722 result = BMP085_read(&pressure, &temperature);
1726 norm_pressure = abs_to_mean_sea_level_pressure(pressure);
1728 sstrncpy (vl.host, hostname_g, sizeof (vl.host));
1729 sstrncpy (vl.plugin, "barometer", sizeof (vl.plugin));
1730 sstrncpy (vl.plugin_instance, "bmp085", sizeof (vl.plugin_instance));
1735 /* dispatch normalized air pressure */
1736 sstrncpy (vl.type, "pressure", sizeof (vl.type));
1737 sstrncpy (vl.type_instance, "normalized", sizeof (vl.type_instance));
1738 values[0].gauge = norm_pressure;
1739 plugin_dispatch_values (&vl);
1741 /* dispatch absolute air pressure */
1742 sstrncpy (vl.type, "pressure", sizeof (vl.type));
1743 sstrncpy (vl.type_instance, "absolute", sizeof (vl.type_instance));
1744 values[0].gauge = pressure;
1745 plugin_dispatch_values (&vl);
1747 /* dispatch sensor temperature */
1748 sstrncpy (vl.type, "temperature", sizeof (vl.type));
1749 sstrncpy (vl.type_instance, "", sizeof (vl.type_instance));
1750 values[0].gauge = temperature;
1751 plugin_dispatch_values (&vl);
1758 * Initialization callback
1760 * Check config, initialize I2C bus access, conversion coefficients and averaging
1763 * @return Zero when successful.
1765 static int collectd_barometer_init (void)
1769 DEBUG ("barometer: collectd_barometer_init");
1771 if (config_device == NULL)
1773 ERROR("barometer: collectd_barometer_init I2C bus device not configured");
1777 if (config_normalize >= MSLP_INTERNATIONAL && isnan(config_altitude))
1779 ERROR("barometer: collectd_barometer_init no altitude configured " \
1780 "for mean sea level pressure normalization.");
1784 if (config_normalize == MSLP_DEU_WETT
1788 ERROR("barometer: collectd_barometer_init no temperature reference "\
1789 "configured for mean sea level pressure normalization.");
1794 i2c_bus_fd = open(config_device, O_RDWR);
1797 ERROR ("barometer: collectd_barometer_init problem opening I2C bus device \"%s\": %s (is loaded mod i2c-dev?)",
1799 sstrerror (errno, errbuf, sizeof (errbuf)));
1803 /* detect sensor type - this will also set slave address */
1804 sensor_type = detect_sensor_type();
1806 /* init correct sensor type */
1810 case Sensor_MPL3115:
1812 MPL3115_adjust_oversampling();
1814 if(MPL3115_init_sensor())
1817 plugin_register_read ("barometer", MPL3115_collectd_barometer_read);
1824 if (averaging_create (&pressure_averaging, config_oversample))
1826 ERROR("barometer: collectd_barometer_init pressure averaging init failed");
1830 if (averaging_create (&temperature_averaging, config_oversample))
1832 ERROR("barometer: collectd_barometer_init temperature averaging init failed");
1836 if (MPL115_read_coeffs() < 0)
1839 plugin_register_read ("barometer", MPL115_collectd_barometer_read);
1846 BMP085_adjust_oversampling();
1848 if (BMP085_read_coeffs() < 0)
1851 plugin_register_read ("barometer", BMP085_collectd_barometer_read);
1855 /* anything else -> error */
1857 ERROR("barometer: collectd_barometer_init - no supported sensor found");
1866 /* ------------------------ plugin register / entry point ------------------------ */
1869 * Plugin "entry" - register all callback.
1872 void module_register (void)
1874 plugin_register_config ("barometer",
1875 collectd_barometer_config,
1878 plugin_register_init ("barometer", collectd_barometer_init);
1879 plugin_register_shutdown ("barometer", collectd_barometer_shutdown);